(06-14-2024, 05:27 PM)Dmitry_3834 提到: This is the third time an error (error code: E009,E010,E011,E012,E013,E014,E015) has randomly appeared when the device is put in standby mode. The first was a few weeks ago, and now two are on the same day. The last two errors looked different. The first time before the error, the display wrote "Settings saved". The second time the error appeared immediately after the text "Standby...". The error cannot be reproduced, it seems to be random. After the first incident, the device was reset to factory settings, but this did not seem to help. I note that the first time I pressed the hardware button on the body of the device, and the last two times the remote control button.
Hi Dmitry_3834,
Was there any storage devices or input sources connected to the mini-i Pro 4 when the device appears the error codes?
(06-14-2024, 05:27 PM)Dmitry_3834 提到: This is the third time an error (error code: E009,E010,E011,E012,E013,E014,E015) has randomly appeared when the device is put in standby mode. The first was a few weeks ago, and now two are on the same day. The last two errors looked different. The first time before the error, the display wrote "Settings saved". The second time the error appeared immediately after the text "Standby...". The error cannot be reproduced, it seems to be random. After the first incident, the device was reset to factory settings, but this did not seem to help. I note that the first time I pressed the hardware button on the body of the device, and the last two times the remote control button.
Hi Dmitry_3834,
Was there any storage devices or input sources connected to the mini-i Pro 4 when the device appears the error codes?
Only the network drive was connected to the device. Nothing else.
(06-18-2024, 06:39 AM)Dmitry_3834 提到: For my audio system I use a power distributor with EMI filters. Matrix mini-i 4 is connected to a separate power filter output.
Hi Dmitry，
Can you connect your mini-i 4 to the power mains directly, and then take a note will the issue happen again.
(06-18-2024, 06:39 AM)Dmitry_3834 提到: For my audio system I use a power distributor with EMI filters. Matrix mini-i 4 is connected to a separate power filter output.
Hi Dmitry，
Can you connect your mini-i 4 to the power mains directly, and then take a note will the issue happen again.
OK. I will observe the device without a filter. I found another bug with the timeline bar... The seconds are not synchronized with the real clock (they can quickly jump by two digits), and after 0:59 the display shows 0:00, and then 1:01.
(06-18-2024, 06:39 AM)Dmitry_3834 提到: For my audio system I use a power distributor with EMI filters. Matrix mini-i 4 is connected to a separate power filter output.
Hi Dmitry，
Can you connect your mini-i 4 to the power mains directly, and then take a note will the issue happen again.
OK. I will observe the device without a filter. I found another bug with the timeline bar... The seconds are not synchronized with the real clock (they can quickly jump by two digits), and after 0:59 the display shows 0:00, and then 1:01.
The issue with the one-minute timeline display error will be resolved in the next firmware update.
Thank you for your valuable feedback.
06-29-2024, 02:59 PM (这个帖子最后修改于: 07-02-2024, 03:30 AM by ExUnoPlura.)
Two issues with mini-i 4 Pro recently discovered:
(1) After power outage when in standby, the mini-i 4 Pro requires power plug to be removed and reinserted in order to discover network again.
(2) I tested a 768 kHz / 24 bit sample file on Roon and MA Remote. On Roon, the maximum sample rate is 384 kHz in device setup and the file is downsampled to 384 kHz. On MA Remote, the file shows as 768 kHz but also shows as 32 bit.
It looks like there are errors in both MA Remote and in the RAAT implementation.
